Replacing a sleeve shouldn’t mean taking down the chandelier or guessing at a size. In most cases, you need three measurements: the internal diameter, the outer or finished diameter, and the finished height.
The important part is knowing what to measure. Candle sleeves (also called chandelier sleeves, candle tubes or chandelier candle covers) are often bespoke and made to order. A small mismatch can mean the replacement won’t slide over the lampholder, or won’t look right once fitted. It’s not as complicated as it looks: measure twice, note everything clearly, then order once.
At Candle Tubes UK, we manufacture bespoke candle sleeves for new lighting designs and restoration projects. Here’s our practical guide to measuring without taking your chandelier down.
Before you start: make it safe
Candle sleeves are decorative components, not electrical parts. You should not need to disconnect wiring or dismantle the chandelier to take these measurements.
Before you reach the fitting:
- Switch off the circuit at the consumer unit first.
- Let the bulbs cool fully before handling them.
- Work on one arm at a time, so you can compare like with like.
- Use a stable stepladder on a level surface; don’t overreach.
- Ask someone to steady the ladder or pass you tools if the fitting is high or awkward to reach.
- Stop if you see damaged wiring, loose connections or other electrical concerns, and contact a qualified electrician.
A second pair of hands is especially helpful when you’re measuring above a staircase or over furniture. Lucky you if you have high ceilings, but they do make safe access all the more important.
What are the three measurements that matter?
Use millimetres if possible and write down each figure as you go. A ruler or digital callipers can help with diameter; a soft tape is useful for height where access is awkward.
1. Internal diameter: what must the sleeve slide over?
Measure the widest part of the lampholder body or socket shell that the candle sleeve needs to pass over. Do not measure the bulb or its screw thread.
The internal diameter (ID) is the opening inside the sleeve. It needs to clear the lampholder accurately: not so tight that you have to force it, and not so loose that the sleeve wobbles.
If an old sleeve is still fitted, remove it only if it lifts off easily. Never force a stuck sleeve. Once the lampholder body is exposed, measure across its widest point. Keep the ruler straight across the centre, or use callipers for a more precise reading.
2. Outer or finished diameter: how wide will the sleeve look?
The outer diameter (OD) is the measurement across the outside of the sleeve. If you know the internal diameter and the wall thickness of the material, use this reckoner:
OD = ID + (wall thickness × 2)
The wall adds to both sides of the tube. For example, a sleeve wall that is 1 mm thick adds 2 mm in total to the outside diameter. Wall thickness varies by material, so confirm it with the manufacturer rather than assuming every candle tube is the same.
If you have an old sleeve that is still round and intact, measure it externally across its widest point. This is useful for matching the finished appearance, but it doesn’t tell you whether its internal diameter is right for the lampholder.

3. Finished height: where should the top edge sit?
Measure from the base of the sleeve, where it sits on the fitting, to the top edge. Make a note of the intended seating point too: it might be the arm, a bobeche (the shallow dish beneath the candle), or a shoulder on the fitting.
Check how that height relates to the bulb. The sleeve should stand clear of the bulb glass rather than touching it, and should not obscure the bulb in a way that changes the look you want. Note whether you want the bulb’s base concealed and how much of the flame-tip or glass you intend to show.
Rule of thumb: The internal diameter must fit over the lampholder body without force, and the finished sleeve must not touch the bulb glass.
Can you measure candle sleeves without taking the chandelier down?
Usually, yes. With the circuit switched off and the bulbs cool, you can measure an accessible arm in place.
- Photograph the fitting before you begin. This gives you a reference for the sleeve’s position and profile.
- Work on one arm. If the existing sleeve slides off easily, set it aside; otherwise, don’t force it.
- Measure the exposed lampholder body across its widest point for the internal diameter required.
- Measure the old sleeve’s outside width, if it is sound and still round, to help establish the finished diameter.
- Measure from the sleeve’s seating point to its top edge for the finished height.
- Write down the measurements and label each one clearly. If the chandelier has several arms, check another arm too; previous repairs can mean the fittings aren’t identical.
For height, keep your tape or ruler straight alongside the sleeve and measure from its actual base, not from a nearby decorative detail. If you cannot reach the fitting without leaning, climbing onto furniture or holding tools in an unstable position, stop and arrange safer access. A quick measurement is not worth a fall.
What if the old sleeve and lampholder measurements disagree?
For the internal fit, the lampholder is usually the true reference: it is the part the new sleeve must pass over. An old sleeve may have warped, cracked, stretched or been an imperfect fit from the start.
Use the old sleeve as a visual reference for its height and outside shape only if it is still in good condition. If its opening is misshapen, don’t use it to decide the internal diameter. Measure the bare lampholder instead, or ask us about our digital measurement service.
A bulb code can help identify the bulb fitting, but it does not specify the outside diameter of the lampholder body. For reference, E10 is MES (Miniature Edison Screw), E14 is SES (Small Edison Screw) and E12-UL is its own US designation. These codes are not substitutes for measuring the sleeve’s fit.
If you’re checking an E14 setup, our guide to the E14 lampholder range explains how the lampholder body and tube dimensions relate.
Does the candle sleeve taper or stay straight?
Not every candle sleeve is a simple cylinder. Some have a straight profile; others taper at the base, so one diameter won’t describe the whole shape. Measure and record the narrowest and widest points, along with where each measurement was taken.
For example, the French GS Range has a 22 mm cylinder profile, while the English Regency Range has a 30 mm base tapered profile. These are distinct shapes, not interchangeable diameter descriptions. If you’re ordering a French GS sleeve, the recommended bulb pairing is an E10 miniature SES Flame Tipped Bulb; always confirm it matches the fitting.
A clear note such as “straight cylinder” or “tapered from base” helps us understand what you’re matching. If you’d like to compare material options, see our candle tube materials comparison.

Rather not measure it yourself? Send us the original part
For a damaged, unusual or hard-to-reach fitting, our specialised digital measurement service can take the guesswork out of ordering. Send us the original sleeve or relevant component so we can assess its dimensions and profile directly. If the sleeve is cracked or warped, include it if you can, but tell us about the damage; it may be more useful as a shape reference than as a dimensional one.
We’ll use the original as a reference for bespoke, made-to-order manufacturing. That’s particularly helpful for restorers, homeowners and designers matching a discontinued profile or a surviving sleeve from a multi-arm chandelier. We also work with a collective of specialist decorators and artists for custom finishing.
Peruse our complete guide to candle sleeves for more on choosing and fitting the right style.
Quick candle sleeve measurement checklist
Screenshot this before you head up the stepladder:
- Circuit switched off at the consumer unit; bulbs cool
- Internal diameter required to clear the lampholder body: ____ mm
- Old sleeve outer diameter across widest point, if sound: ____ mm
- New sleeve outer or finished diameter required: ____ mm
- Finished height, base to top edge: ____ mm
- Profile: straight / tapered / other: ____
- Narrowest and widest profile measurements, if tapered: ____ / ____ mm
- Bulb glass clears sleeve; note how much bulb should show
- Number of sleeves required: ____
Candle sleeves FAQ
How do I measure a candle sleeve?
Measure the lampholder body for the required internal diameter, the sleeve’s outside for its finished diameter, and the sleeve from base to top edge for height. Note any taper and where the sleeve sits.
What if my sleeve is cracked or warped?
Don’t rely on its inner diameter. Measure the bare lampholder for the fit, and use the damaged sleeve only as a reference for height or profile if it still shows the original shape. You can also send the original part to us for digital measurement.
Do I measure the bulb or the lamp holder?
Measure the lamp holder’s outer body, the part the sleeve slides over, not the bulb or its screw thread. The bulb code alone doesn’t determine the sleeve size.
Can I order just one sleeve?
Please contact us to discuss your requirement. We make bespoke candle sleeves to order and can advise on individual replacement enquiries as well as larger projects.
How long does a bespoke order take?
Timing depends on the specification, material, finish and quantity. Contact Rachel’s office on 0330 113 7842 for current availability and a lead-time estimate.
Candle Tubes UK is the UK’s leading manufacturer of bespoke candle tubes, sleeves and covers for lighting manufacturers, restorers, interior designers and homeowners. Explore our ranges at www.candletubes.co.uk, www.candletubes.com and www.candletubes.eu.

